Hyppää pääsisältöön
M1003-pysäytyskytkin on yksinkertainen induktiivinen akselinopeuden valvontalaite. Itsenäinen yksikkö antaa signaalin, kun akselin pyörintä on pysähtynyt. Laitetta voidaan käyttää prosessinhallintaan, liikkeentunnistukseen ja pysähtyneen akselin ilmaisemiseen. M100-laitteen kotelon päässä oleva induktiivinen anturilaite havaitsee metallisen kohteen. Kohde voi olla pultin pää tai akseliin kiinnitetty laite. M1003-pysäytyskytkin ei vaadi kalibrointia, ja se antaa syötteen, kun akselin pyörintä on pysähtynyt.
- 24–240 VAC/VDC-monijännitevirransyöttö
- 2-johtiminen
- IP66-luokitus
- M18 × 1.0 ISO-kierteinen nailonrunko
- Vihreät ja siniset LED-valot, jotka ilmaisevat syötteen tilan
- 6 mm:n tunnistusalue
- Kalibrointia ei tarvita
- 4 sekunnin käynnistysviive
Belt Conveyor
Bucket Elevator
Chain Conveyor
Screw Conveyor
Specifications
| | ||
| Specification | Value | |
| Supply Voltage: | 24 to 240 VAC/VDC | |
| Supply Fusing: | Supply to be fused at 500mA maximum | |
| Switching Capacity: | 50mA maximum | |
| Saturation Voltage: | 5.5 Volts maximum (output on) | |
| Leakage Current: | 1.0 mA maximum (output off) | |
| Ambient Temperature: | 5°F (-15°C) to +122°F (+50°C) | |
| Output State: | FET | |
| Sensing Range: | 6 mm (15/64”) maximum on ferrous metal at 77°F (25°C) | |
| Input Pulse Range: | 20 to 3,600 pulses per minute (PPM) maximum | |
| Start-Up Delay: | 4 seconds | |
| Trip Point: | zero speed | |
| Enclosure: | Nylon - ISO threaded 18 mm by 1.0 mm pitch | |
| Relative Humidity: | 90% RH | |
| LED Indicators: | Blue - Target Sensed, Green - Rotation Detected | |
| Connections: | 2 wire, 3m long cable. | |
| Protection: | IP66 |
Downloads
Accessories
SpeedMaster™
The SpeedMaster™ with Pulse Pilot is the only device that accurately tests the calibration of a speed switch, and allows testing of the 10% alarm and 20% shutdown features of the sensor while installed on the machine shaft.
The SpeedMaster™ operates in two modes. Input mode is used to measure the pulse rate at normal speed. Output mode will allow the user to simulate belt underspeed for testing purposes.
The Pulse Pilot fits between the gap between the sensor and the target. The Pulse Pilot will have no effect on the operation of the speed switch until it is connected to the SpeedMaster™ and set to Output mode.
4B Sensor Mounting Kit
The 4B Sensor Mounting Kit is able to securely mount barrel sensors in position, including 4B’s range of 18 & 30mm wide inductive sensors.
Made of Stainless Steel and Nylon 66, giving corrosion resistance as well as abrasion resistance and high melting points, the brackets are ideal for harsh environments.
A flexible mounting head and foot can be rotated independently before being locked in the required position using the supplied screws.
4B Speed Relay (USR)
The Speed Relay is a microprocessor controlled digital speed monitor for use with 2, 3, 4 wire NPN/PNP sensors, 4B’s WDA range of sensors or Contact sensor inputs, with a user programmable electromechanical relay and PhotoMOS Solid State Relay (SSR) outputs. The Speed Relay has a 160x80 pixel LCD display to provide information, and 3 front panel buttons to program settings.
Monitors
X400 Elite Alarmswitch
The X400 Elite is a microprocessor controlled low cost alarm indicator panel for use with level indicators, hazard controls and limit switch sensors. The X400 accepts signals from different sources in up to 8 zones, and is able to cause alarm and shutdown of the machine when an alarm condition has been detected. Alarm and status LEDs on the lid of the X400 provide quick location of alarm conditions. Alarm muting can be performed at the panel or by an optional remote push button to silence external alarms. If the system is muted, it will automatically reactivate when a new alarm is triggered. Testing can also be activated at the panel, providing full system verification.
FAQ's
Tuotetiedoissa mainitaan ”kuorma”. Mikä se on, ja kuinka suuri sen täytyy olla?
Kuorma ei ole vastus, vaan se viittaa mihin tahansa kohteeseen, joka ottaa virtaa (esimerkiksi PLC-tulo tai pistokantarele) ja käyttää sitä alle 200 mA.
Kun 2-johtiminen M300 tarkastetaan jännitemittarilla, se näyttää aina täyden jännitteen riippumatta siitä, pyöriikö akseli vai ei. Miksi anturi ei muuta tilaa?
Anturi ei toimi oikein ennen kuin siihen on kytketty kuorma. Enimmäisvirta anturin kautta on 200 mA.
Images
