B 型斗提机畚斗

中型斗提畚斗

 B 型畚斗一般用于粘稠物料在低速下的输送和自由流动性物料在较高的速度下和更紧密的畚斗间距下的输送

 

B-type elevator bucket
Product Features: 
  • 无缝钢深拉冲压成型,没有焊缝、没有接头
  • 适合粘稠物料的低速输送
  • 适合自由流动性物料在较高速度下和更紧密的畚斗间距条件下的输送
  • 良好的通用中型畚斗

B-Type Bucket
A
(mm)
B
(mm)
C
(mm)
D
(mm)
T
(mm)
Weight
(kg)
Capacity (L)
Z2 (Gross)
Capacity (L)
Z3 (Water)
Holes
No.
E
(dia mm)
F
(mm)
G
(mm)
B10645157321.20.080.10.06to customer spec
B17767067350.90.10.180.1to customer spec
B21957067351.20.140.220.13to customer spec
B381028683351.20.180.380.2to customer spec
B441278683351.20.230.460.23to customer spec
B631278989381.20.270.550.3to customer spec
B661408989381.20.290.620.32to customer spec
B701528989381.20.320.640.34to customer spec
B114 P+R1529598381.50.410.750.4228.78325
B1141529598381.50.410.750.42to customer spec
B11715295983830.790.750.42to customer spec
B134 HDP2201061045040.181.150.6228.712736
B134 P+R2169598381.50.571.150.5728.712725
B1352299598381.50.591.250.6to customer spec
B135 P+R2299598381.50.591.250.628.712725
B147152117108541.50.521.10.59to customer spec
B1491521171085430.981.10.59to customer spec
B151178117108541.50.541.150.65to customer spec
B1531781171085431.021.150.65to customer spec
B155203117108541.50.641.40.83to customer spec
B1572031171085431.21.40.83to customer spec
B166127121114541.20.360.950.5to customer spec
B167127121114541.50.430.950.5to customer spec
B167 P+R152121114541.50.430.950.528.77032
B175152121114541.50.541.10.64to customer spec
B1881911211145420.771.40.83to customer spec
B198229121114541.20.571.751to customer spec
B2002291211145420.881.751to customer spec
B2012291211145431.291.751to customer spec
B205254120114551.50.821.91.1to customer spec
B211178130114541.50.591.450.8to customer spec
B219203130114541.50.641.650.92to customer spec
B2212031301145431.291.650.92to customer spec
B2342411301145431.5621.15to customer spec
B2372541301145421.092.11.25to customer spec
B2382541301145431.542.11.25to customer spec
B2422791301145431.722.351.35to customer spec
B258203133127541.50.791.850.9to customer spec
B263229133127541.50.8621to customer spec
B2662291331275431.5621to customer spec
B2692541331275421.132.251.15to customer spec
B278305133127541.512.81.35to customer spec
B28130513312754322.81.35to customer spec
B283*333140140601.51.183.752to customer spec
B2972031521495731.632.251to customer spec
B30125415214957322.751.4to customer spec
B303305152149571.51.183.51.75to customer spec
B304 HDP298145149486.50.4731.18to customer spec
B304 P+R3051521495721.563.51.7548.751-102-5144
B3053051521495732.313.51.75to customer spec
B3073811521526721.934.852.5to customer spec
B307 P+R3811521526721.934.852.548.776-127-76
B3642541521788321.543.62to customer spec
B3652541521788332.273.62to customer spec
B3233051781817932.835.52.75to customer spec
B3283561781817933.526.523.25to customer spec
B3353051782067933.025.752.5to customer spec
B3393812101848634.0884.25to customer spec
B34045723521010235.08137to customer spec
B3414572352101024.76.26137to customer spec

* Non stock item - Only made to order.
HDP - High density polyethylene with standard recessed holes.
P + R - With standard recessed holes.

FAQ - Elevator Buckets

什么是高效斗提机畚斗? 
全部满足下列 5 个特点才能称得上是高效畚斗:具有平滑的挖掘曲面,工作面没有折线;没有多余的侧翼边;安装在皮带上垂直方向畚斗间距小;畚斗底部收敛,可以堆叠,能极大减少运输和存储成本。了解更多,请点击这里。
     
为什么要使用浅型斗提机畚斗?
采用浅型畚斗设计的目的是为了减少畚斗安装间距,提升斗提机整体提升能力。为此,有些类型的畚斗通过改进可以实现这样的目的,也有些畚斗本身就是浅型设计。浅型畚斗对潮湿物料、粘滞性物料的填充和抛料都不是很有效。经过改造后,斗提机提升能力可以增加,但畚斗整体重量因数量的增加也大大增加了,所以皮带的抗拉强度要求、皮带轮轴径和电机功率可能都要作相应升级。请联系4B工程部门了解提高斗提机能力的最佳解决方案。
     
为什么要在畚斗底部加排气孔?  
畚斗底部的排气孔有助于轻抛物料或粉状料的填充和抛料。物料进入畚斗时带进来的空气被挤压在畚斗底部,畚斗底部的排气孔让这些空气能顺利排出,避免物料被空气弹出畚斗,回落到斗提腿中;抛料时,排气孔有助于空气再次进入进入畚斗,避免封闭畚斗底部产生的真空吸住物料,降低抛料效率。
     
 CC 型畚斗能与  Starco 型畚斗互换吗?
Starco 型畚斗是浅型畚斗,使用这种畚斗的目的是为了在皮带上排布尽可能多的畚斗,用其他型号替代 Starco 型畚斗之前请与 4B 公司工程部门联系确认。
     
我需要用多长的畚斗螺栓?
安装畚斗之前用这个简单公司进行螺栓长度计算:螺栓长度 = 皮带厚度+畚斗背部厚度+螺栓垫片厚度+螺母厚度 +1/4 英寸余量

什么是“挖掘”型畚斗(斗提机侧壁清洁畚斗)
有些物料能在斗提机尾箱壁上形成坚硬的壳层,沉积的粉状物料时间一长也会变得坚硬无比,这两个因素都会给斗提机畚斗带来过快的磨损,影响畚斗寿命。所以设计了宽度稍宽于正常宽度有着一定“挖掘”作用的畚斗,能在一定程度上破坏并清除结壳硬化的物料,阻止对畚斗的额外磨损。通常“挖掘”畚斗为钢制,但有时候高强度的尼龙畚斗也可以起到“挖掘”畚斗的作用。
     
我要用几个“挖掘”畚斗?
绝大多数情况下,每 9 个标准畚斗可用1个“挖掘”畚斗
     
我可以在搭接型皮带上安装畚斗吗?
搭接型的皮带在搭接处厚度是正常皮带的2倍,安装在此处的畚斗会比正常位置的畚斗向外更突出,一般情况下不会有什么问题,但如果出现干涉,你可以用小一号的畚斗,或将畚斗前嘴部切掉一些(半英寸)。
     
搭接皮带时,搭接处的皮带长度最少要多长?
 搭接处的皮带长度为皮带宽度的最少 3 倍。  
     
 皮带轮防磨保护层多长时间需要更换? 
每次更换皮带时都需要更换皮带轮上的防磨层。