M1003 Stopswitch
Stopped Motion Monitor
M1003V10AI

The M1003 Stopswitch is a simple inductive shaft speed monitoring device. The self-contained unit, which signals when the shaft has stopped rotating. It can be used for process control, motion detection and stopped shaft indication. An inductive sensing device located in the nose of the M100 enclosure will detect a metal target. This target can be an existing bolt head or device attached to a shaft. The M1003 Stopswitch requires no calibration and provides an output when the shaft has stopped rotating.

M100 Stopswitch
Product Features
  • 24-240 VAC/VDC multi voltage power supply
  • 2-wire
  • IP66 rated
  • M18 x 1.0 ISO threaded nylon body
  • Green and Blue LEDs showing output state
  • 6 mm detection range
  • No calibration needed
  • 4s start up delay
Electronics Application

Belt Conveyor

Belt Conveyor

Bucket Elevator

Bucket Elevator

Chain Conveyor

Chain Conveyor

Screw Conveyor

Screw Conveyor
Certification

ATEX

ATEX
Bild
ATEX Logo

UKEx

UKEx
Bild

IECEx

IECEx
Bild
IECExv3

EACEX

EACEX
Bild
EACEx

CnEx

CnEx
Bild
Nepsi

CSA

CSA
Bild
CSA logo

CE

CE
Bild
CE Logo

    M1003 Dimensions

    
    Specification Value
    Supply Voltage: 24 to 240 VAC/VDC
    Supply Fusing: Supply to be fused at 500mA maximum
    Switching Capacity: 50mA maximum
    Saturation Voltage: 5.5 Volts maximum (output on)
    Leakage Current: 1.0 mA maximum (output off)
    Ambient Temperature: 5°F (-15°C) to +122°F (+50°C)
    Output State: FET
    Sensing Range: 6 mm (15/64”) maximum on ferrous metal at 77°F (25°C)
    Input Pulse Range: 20 to 3,600 pulses per minute (PPM) maximum
    Start-Up Delay: 4 seconds
    Trip Point: zero speed
    Enclosure: Nylon - ISO threaded 18 mm by 1.0 mm pitch
    Relative Humidity: 90% RH
    LED Indicators: Blue - Target Sensed, Green - Rotation Detected
    Connections: 2 wire, 3m long cable.
    Protection: IP66

    SpeedMaster™

    4b Speedmaster - Testeur de contrôleur de rotation
    SpeedMaster™

    The SpeedMaster™ with Pulse Pilot is the only device that accurately tests the calibration of a speed switch, and allows testing of the 10% alarm and 20% shutdown features of the sensor while installed on the machine shaft.

    The SpeedMaster™ operates in two modes. Input mode is used to measure the pulse rate at normal speed. Output mode will allow the user to simulate belt underspeed for testing purposes.

    The Pulse Pilot fits between the gap between the sensor and the target. The Pulse Pilot will have no effect on the operation of the speed switch until it is connected to the SpeedMaster™ and set to Output mode.

    PRODUCT DETAILS

    Whirligig®

    4B Whirligig shaft sensor mount
    Whirligig®

    The Whirligig® is a fully guarded target for easy mounting of motion sensors. It is a universal shaft sensor mount suitable for all industry standard cylindrical or DIN style inductive sensors including 4B's M100, M300, and M800 speed switch sensors.

    The sensor bolts to the Whirligig base plate and the complete assembly either bolts to the machines shaft through a M12 tapped hole, or is connected magnetically using 4B’s patented Mag-Con™ adaptor. Shaft or machine vibration does not affect the performance of the sensor, as the whole assembly moves with the shaft. With the Whirligig, installation of speed sensors is now simple, safe and reliable.

    PRODUCT DETAILS

    4B Sensor Mounting Kit

    4B sensor mounting kit
    4B Sensor Mounting Kit

    The 4B Sensor Mounting Kit is able to securely mount barrel sensors in position, including 4B’s range of 18 & 30mm wide inductive sensors.

    Made of Stainless Steel and Nylon 66, giving corrosion resistance as well as abrasion resistance and high melting points, the brackets are ideal for harsh environments.
    A flexible mounting head and foot can be rotated independently before being locked in the required position using the supplied screws.

    PRODUCT DETAILS

    4B Speed Relay (USR)

    4B speed relay
    4B Speed Relay (USR)

    The Speed Relay is a microprocessor controlled digital speed monitor for use with 2, 3, 4 wire NPN/PNP sensors, 4B’s WDA range of sensors or Contact sensor inputs, with a user programmable electromechanical relay and PhotoMOS Solid State Relay (SSR) outputs. The Speed Relay has a 160x80 pixel LCD display to provide information, and 3 front panel buttons to program settings.

    PRODUCT DETAILS

    X400 Elite Alarmswitch

    X400 Elite
    X400 Elite Alarmswitch

    The X400 Elite is a microprocessor controlled low cost alarm indicator panel for use with level indicators, hazard controls and limit switch sensors. The X400 accepts signals from different sources in up to 8 zones, and is able to cause alarm and shutdown of the machine when an alarm condition has been detected. Alarm and status LEDs on the lid of the X400 provide quick location of alarm conditions. Alarm muting can be performed at the panel or by an optional remote push button to silence external alarms. If the system is muted, it will automatically reactivate when a new alarm is triggered. Testing can also be activated at the panel, providing full system verification.

    PRODUCT DETAILS

    In the product documentation, there is a reference to "load". What is it and how big does it have to be?  
     Load is not a resistor, it is referring to any item that pulls current (PLC input, ice cube relay, etc.) and draws less than 200 mA.  
     

    When checking the 2 wire M300 with a voltage meter, it is always showing full voltage no matter if the shaft is turning or not. Why is the sensor not changing states?  
      The sensor will not function correctly until a load is connected to it, maximum current through the sensor is 200 mA..  

    Hazard Monitoring Design Service

    Hazard Monitoring Design Service

    Preventative maintenance can help reduce the risk of equipment failure and consequent downtimes. When it comes to monitoring your bucket elevators and belt conveyors, 4B can recommend you the ideal combination of sensors and monitoring systems to suit your requirements and budget.

    4B provides an extensive range of their own ATEX / IECEx / CSA approved hazard monitoring systems, misalignment switches and bearing temperature monitors and level controls. We can offer you anything from a replacement sensor to a fully integrated hazard monitoring system which can be operated either as a stand-alone system or connected to your PLC.

    And if you do not want to install hazard monitoring sensors on every piece of equipment in your plant straightaway, we can offer you a scalable solution starting with carefully chosen equipment and systems that can be expanded at a later date to encompass other machines in the plant.

    We can also offer you an installation service, and we do provide a competent after-sales technical service to help you overcome any technical problems with your monitoring equipment.

    To get a recommendation from our engineers, please fill in the electronics questionnaire below. Please fill this form in as accurately as possible to allow us to deal with your enquiry more effectively.

    Preventative maintenance can help reduce the risk of equipment failure and consequent downtimes. When it comes to monitoring your bucket elevators and belt conveyors, 4B can recommend you the ideal combination of sensors and monitoring systems to suit your requirements and budget.

    4B provides an extensive range of their own ATEX / IECEx / CSA approved hazard monitoring systems, misalignment switches and bearing temperature monitors and level controls. We can offer you anything from a replacement sensor to a fully integrated hazard monitoring system which can be operated either as a stand-alone system or connected to your PLC.

    And if you do not want to install hazard monitoring sensors on every piece of equipment in your plant straightaway, we can offer you a scalable solution starting with carefully chosen equipment and systems that can be expanded at a later date to encompass other machines in the plant.

    We can also offer you an installation service, and we do provide a competent after-sales technical service to help you overcome any technical problems with your monitoring equipment.

    To get a recommendation from our engineers, please fill in the electronics questionnaire below. Please fill this form in as accurately as possible to allow us to deal with your enquiry more effectively.

    Contact Details

    Elevator Information

    Monitoring Requirements (Check All that Apply):

    Conveyor Information

    Monitoring Requirements (Check all that Apply):

    Silo/ Bin Information

    Monitoring Requirements (Check all that Apply):

    If you would like to send us a technical drawing or document with your enquiry, please send to 4b-uk@go4b.com.

    CAPTCHA
    Den här frågan testar om du är en mänsklig besökare och förhindrar automatiska spaminsändningar.