X400 Elite Alarmswitch
Centralized Alarm Monitoring System
X4004V4CAI, X4004V46CAI

The X400 Elite is a microprocessor controlled low cost alarm indicator panel for use with level indicators, hazard controls and limit switch sensors. The X400 accepts signals from different sources in up to 8 zones, and is able to cause alarm and shutdown of the machine when an alarm condition has been detected. Alarm and status LEDs on the lid of the X400 provide quick location of alarm conditions. Alarm muting can be performed at the panel or by an optional remote push button to silence external alarms. If the system is muted, it will automatically reactivate when a new alarm is triggered. Testing can also be activated at the panel, providing full system verification.

X400 Elite
Product Features
  • Centralized Alarm Monitoring for up to 8 Zones
  • Multiple Alarm Inputs from Different Sensors
  • LED Alarm Indication
  • Alarm Mute - Reactivation on New Alarm
  • Push Button Testing Feature
  • Optional PLC Board
Electronics Application

Belt Conveyor

Belt Conveyor

Bucket Elevator

Bucket Elevator

Silos & Storage

Silos & Storage
Certification

ATEX

ATEX
Kuva
ATEX Logo

UKEx

UKEx
Kuva

IECEx

IECEx
Kuva
IECExv3

CnEx

CnEx
Kuva
Nepsi

CSA

CSA
Kuva
CSA logo

CE

CE
Kuva
CE Logo

GOST-R

GOST-R
Kuva
gost-r-mark

    M1003 Stopswitch

    M100 Stopswitch
    M1003 Stopswitch

    The M1003 Stopswitch is a simple inductive shaft speed monitoring device. The self-contained unit, which signals when the shaft has stopped rotating. It can be used for process control, motion detection and stopped shaft indication. An inductive sensing device located in the nose of the M100 enclosure will detect a metal target. This target can be an existing bolt head or device attached to a shaft. The M1003 Stopswitch requires no calibration and provides an output when the shaft has stopped rotating.

    PRODUCT DETAILS

    M3003, M3008 & M3007 Slipswitch

    M3003 & M3007 Slipswitch
    M3003, M3008 & M3007 Slipswitch

    The M300 Slipswitch is an easy-to-use inductive proximity shaft speed monitoring device with an adjustable 0 - 30 second start-up delay, all housed in a 30 mm diameter moulded body. The self-contained unit has a single set point, which signals when the shaft speed has dropped by 20% of normal running speed. It is used for detecting dangerous slow down and underspeed conditions on conveyors, bucket elevators, air locks, mixers, fans, grinders and many other machines. 

    No connection is necessary between the sensor and the equipment being monitored. The proximity sensor detects a stud or bolt mounted on a shaft, or other suitable target. Ideally, the target should be of ferrous metal, but non-ferrous metal will be detected at a shorter range. Maximum range of ferrous targets is 8 mm (5/16”) and for non-ferrous targets is 5 mm (6/16”), assuming a 20 mm (3/4”) diameter target. Smaller targets may be used but operating distances will be reduced.

    PRODUCT DETAILS

    M800 Speed Switch

    M800 Elite speed switch
    M800 Speed Switch

    The M800 Elite Speed Switch is designed to detect belt slip, belt underspeed, stop motion, low speed or zero speed on bucket elevators, conveyors, airlocks, mixers, fans, grinders and many other rotating machines. Totally sealed and simple to calibrate, the M800 Elite works in the harshest of conditions.

    An inductive sensing device located in the nose of the M800 Elite enclosure will detect a metal target. This target can be an existing bolt head or device attached to a shaft. During installation the M800 Elite is set to the normal machine shaft RPM by calibrating with the magnet provided. The internal microprocessor sets the alarm and shutdown relays.

    PRODUCT DETAILS

    Touchswitch™

    4b Touchswitch sensor
    Touchswitch™

    The Touchswitch is an electro-mechanical limit switch with no moving parts, which detects tracking and misalignment problems on bucket elevators and conveyors. When a belt misaligns or a pulley moves over and contacts the sensor, the built in solid-state electronic circuitry detects the lateral force of the belt or pulley and activates a voltage free solid state relay output. This output signal is used to immediately alarm and ultimately shutdown the machine.

    The face of the sensor is made from hardened and annealed stainless steel, not soft brass or aluminium, so wear life is longer when a belt contacts it. The Touchswitch is not affected by dust or material build up and will still work when completely covered by material. An external test wheel allows for quick and simple sensor/system testing. The sensors are usually installed in pairs on opposite sides of the machine. The sensors can be connected directly to a PLC input, or for greater safety, to a central independent monitoring system, such as Watchdog Super Elite, IE-Node or the T500 Hotbus system.

    PRODUCT DETAILS
    level indicators

    4B offer a variety of level indicators to detect high / low levels of bulk granular material in bins, tanks and silos. The range includes capacitance point level indicators, rotary paddle switches and capacitance proxy  level / plug detectors. 4B level sensors can be connected to a PLC or to one of 4B’s hazard monitoring systems to provide alarm and/or shutdown of your machinery.

    View our full Electronics Catalogue here.

     
    Level Indicators
    Category color
    #1455fc
    Slider
    Kuva
    level monitorins
    VIEW PRODUCT RANGE