Godets Type A
Godets d'élévateurs - forme peu profonde
A29, A32, A59, A69, A72

Utilisé pour les produits collants ou à vitesse plus rapide et avec un espacement plus petit.

A-type elevator bucket
Product Features
  • Godet de fabrication emboutie
  • Pour produits colmatants à vitesse lente
  • Pour produits coulants à vitesse plus rapide et avec un espacement plus petit
Material
Acier
Use by Industry
Agriculture
Use by Product
Céréales,
Pellets & Produits légers
    Godet type A - drawing
    A-TYPE A B C D T Weight Capacity Capacity Holes E F G
    bucket (mm) (mm) (mm) (mm) (mm) (kg) Z2 (total) Z3 (water) No. (dia mm) (mm) (mm)
    A29 152 108 124 38 1.2 0.39 0.96 0.34 to customer spec
    A32 178 108 124 38 1.5 0.57 1.2 0.44 to customer spec
    A59 229 121 143 48 3 1.7 1.88 0.75 to customer spec
    A69 254 149 187 67 3 2.31 3.65 1.47 to customer spec
    A72 305 168 229 86 3 3.27 3.24 2.5 to customer spec

    Trous percés selon demande.

    FAQ - Elevator Buckets

    FAQ - Elevator Buckets

    What is a HIGH EFFICIENCY elevator bucket?  
    HIGH EFFICIENCY elevator buckets incorporate all five of the following characteristics: a smooth interior front face with no "breaks", wing-less side walls, close vertical placement on the elevator belt, a tapered bottom and the ability to nest for shipping and storage.  For more details, CLICK HERE  
         
    Why use Low Profile elevator buckets?  
    Low profile elevator buckets are created to achieve the closest vertical spacing possible on the elevator belt, thereby optimizing the system for the greatest potential capacity.  Some styles of elevator bucket require modification and others are low profile by standard design.  Wet or sluggish inputs do not generally load and discharge well in low profile buckets.  Due to the extra capacity that is generated and the weight of the additional buckets and material, belt PIW rating, pulley shaft diameters and motor HP may have to be upgraded.  Check with 4B engineering department about the best way to get the most capacity out of your elevator leg.  
         
    Why add vent holes to the bottom of an elevator bucket?  
    When elevating fluffy or powdery materials, vent holes in the bottom of the elevator bucket allow it to fill and discharge more efficiently.  As material enters the bucket, it encounters a pillow of air resting in the bottom.  Vent holes provide an escape path for this pillow of air, so that the entering material does not bounce out of the bucket and back down the elevator leg casing.  Upon discharge, the vent holes allow air to re-enter the bucket at the material exits, releasing any vacuum that might hold it the bucket too long, creating down legging.  
         
    Are CC style elevator buckets interchangeable with Starco elevator buckets?  
    Starco elevator buckets have a special shallow geometry and are intended to be placed extremely close together on the elevator belt.  Therefore, you should check with the 4B engineering department before replacing Starco elevator buckets with any other brand or design.  
         
    How long of an elevator bolt do I need?  
    When installing buckets on an elevator belt, use this simple formula: 
    (belt thickness + bucket back thickness + washer thickness + nut thickness + 1/4 inch)  
         
     

    What is a "digger" bucket?  
    Some materials can form a hardened crust along the side wall of the elevator boot, and powders sitting over time can become rock hard.  Both of these issues can cause premature elevator bucket wear.  Digger buckets are designed to have slightly more width and projection than standard buckets, thereby "digging" through or breaking apart the hardened material, helping to prevent added wear to the standard buckets.  Digger buckets are traditionally made from steel, however nylon buckets may also be used depending on the application.  
         
    How many digger buckets do I need?  
    For most applications, use one digger bucket for every nine standard buckets.  
         
    Can I use buckets on an overlap splice?  
    An overlap splice doubles the thickness of the belt, so a bucket's projection will increase on the overlap.  Usually this will not cause a problem, but if it does, you can use buckets with one inch less projection or cut the tip of each bucket by half an inch on the spliced area.  
         
    When using an overlap splice, how much extra belt should I use for the splice?  
    The length of the splice should be three times the width of the belt.  
         
    How often should I replace head pulley lagging?  
    Lagging should be replaced every time the elevator belt is replaced.

    Service Design pour Elévateurs à Godets

    Service Design pour Elévateurs à Godets

    A 4B, nous avons conçu des centaines d'élévateurs a godets, pour toutes les applications, y inclus l'alimentation animale, céréales, ciment, sable, charbon et autres.

    Profitez de notre service de design gratuit. Qu'il s'agit d'un élévateur nouveau ou existant, notre equipe d'ingénieurs peut vous donner une recommandation technique détaillée, avec une capacité et des caractéristiques de décharges optimales.

    Pour recevoir une calculation gratuite

    remplissez le formulaire ci-dessous. -Tous les champs doivent être renseignées. .

    A 4B, nous avons conçu des centaines d'élévateurs a godets, pour toutes les applications, y inclus l'alimentation animale, céréales, ciment, sable, charbon et autres.

    Profitez de notre service de design gratuit. Qu'il s'agit d'un élévateur nouveau ou existant, notre equipe d'ingénieurs peut vous donner une recommandation technique détaillée, avec une capacité et des caractéristiques de décharges optimales.

    Pour recevoir une calculation gratuite

    remplissez le formulaire ci-dessous. -Tous les champs doivent être renseignées. .

    Contact

    Votre Elévateur

    If you would like to send us a technical drawing or document with your enquiry, please send to 4b-france@go4b.com.

    CAPTCHA
    Cette question sert à vérifier si vous êtes un visiteur humain ou non afin d'éviter les soumissions de pourriel (spam) automatisées.